MWT-0618S-12P1/0618z-12p1 MWT-0618S-12P1/0618z-12p1 * when calculating tch, use fet vds = 6.0 volts and fet ds = 175 ma 6.0-18.0 ghz balanced amplifier module 6.0-18.0 ghz balanced amplifier module email: info@mwtinc.com www.mwtinc.com 4268 solar way fremont california 94538 phone: (510) 651-6700 fax: (510) 651-2208 4268 solar way fremont california 94538 phone: (510) 651-6700 fax: (510) 651-2208 frequency (ghz) frequency (ghz) typical small signal gain (db) 29 28 27 26 25 6 12 18 6 12 18 27.0 dbm p-1db typical specifications at 25 c 4.0 db small signal gain 15.0 db input/output return loss 350 ma @ +8v uses two mwt-12hp gaas fet devices electrical specifications (ta=25 c) symbol parameters units min typ max freq frequency range ghz 6.0 18.0 ssg small signal gain db 3.7 4.0 g/ f ssg flatness +/-db 0.4 0.6 g/ t ssg variation over temperature db/ c -.012 p-1db output power at 1db compression dbm 26.0 27.0 psat output power at 6 db compression dbm 28.0 p/ t p-1db variation over temperature db/ c -.008 ip3 third order intercept point dbm 37.0 2nd har 2nd harmonic at pout=27.0 dbm dbc -21.0 2nd har 2nd harmonic at pout=28.0 dbm dbc -16.0 nf noise figure db 7 .5 vswr in input vswr ----- 1.5:1 1.7:1 vswr out output vswr ----- 1.5:1 1.7:1 iso reverse isolation db -20.0 vdd power supply voltage +v 7.9 8.0 8.1 idd small signal module current ma 350.0 450.0 rth thermal resistance including fet* c/w 55.0 5.0 4.0 3.0 7.5 db noise figure typical output power p-1db (dbm) all rights reserved. microwave technology, inc. all specifications subject to change without notice.
MWT-0618S-12P1/0618z-12p1 MWT-0618S-12P1/0618z-12p1 6.0-18.0 ghz balanced amplifier module 6.0-18.0 ghz balanced amplifier module notes: construction email: info@mwtinc.com www.mwtinc.com 4268 solar way fremont california 94538 phone: (510) 651-6700 fax: (510) 651-2208 4268 solar way fremont california 94538 phone: (510) 651-6700 fax: (510) 651-2208 construction: notes: .055 max. w/caps & bond wires .041 .025 .390 .390 .500 .500 .110 .110 .095 .095 dc .08 .08 .405 .405 .08 .08 rf in rf out rf out z s o o o o .062 .062 .088 .088 .158 .158 .184 .184 .246 .246 the 15 mil alumina substrates and 10 mil copper fet ridge are brazed onto the 25 mil carrier using auge preform. the gaas fets are attached to the cu ridge using ausn preform. all capacitors are attached using ausn preforms. the flanges are designed to accommodate 0-80 unf-2a socket or fillister head screws on .400 center-to-center hole spacing. the modules are mechanically and electrically designed to be cascaded. configurations 1. dimension in inches 2. tolerance: xxx= +/- .005 xx= +/- .01 1. custom module specifications and/or custom module mechanical configurations are available. 2. operating temperature range is -55 degrees celsius to +95 degrees celsius. 3. all modules are serialized and shipped with data measured at 25 degrees celsius. data includes swept small signal gain, swept input and output return loss. noise figure and p-1db are measured in 1 ghz increments. special module testing is available. 4. test fixtures are available. 5. microwave technology reserves the right to ship modules with performance above the typical specifications. rf in dc dc dc all rights reserved. microwave technology, inc. all specifications subject to change without notice.
|
